Home
About
About Us FAQ
Epoxy Flooring
Epoxy Flooring Garage Epoxy Residential Epoxy Commercial & Industrial Warehouse Epoxy Automotive Epoxy Aircraft Hangar Epoxy Healthcare Epoxy Restaurant & Kitchen Metallic Epoxy Basement Epoxy Parking Garage Epoxy Epoxy Repair
Concrete Services
Concrete Polishing Polished Concrete Floors Concrete Grind & Seal Stained Concrete Floors
Floor Coatings
Polyaspartic Coating Polyurea Coating Urethane Cement ESD Anti-Static Epoxy Epoxy Flake System Get a Free Quote
Aviation Flooring

Aircraft Hangar Floor Coating Requirements:
Fuel, Skydrol and Loads

A specification checklist for Nashville hangar floors: fuel and hydraulic fluid resistance, aircraft and equipment loads, slope and drains, joints, light, traction and cure time.

Quick answer: a hangar floor coating has to survive aviation fuels, hydraulic fluid and de-icing fluid, carry concentrated aircraft and equipment loads, hold its slope to the drains, and stay easy to clean and light enough to see by. A specification that names each of those, in writing, is what separates a hangar floor from an ordinary commercial floor. For the local airport and lease context, start with our aircraft hangar epoxy flooring Nashville page, then use this guide to write the requirements.

This post stays on specification. It does not repeat airport descriptions or pricing, which live in our aircraft hangar epoxy flooring guide for Nashville, and it leaves static control standards to our ESD anti-static flooring guide. What follows is a checklist a hangar owner, FBO or facility manager can hand to a bidder so every quote covers the same ground.

What Is Different About a Hangar Floor

A hangar floor differs from a warehouse or garage floor because it combines chemical exposure that is uncommon elsewhere, very concentrated loads and a code environment that treats the building as a fuel-handling space. Each of those pushes the specification in a different direction, and a system chosen for one can fail on another.

A typical warehouse floor sees forklift wheels and the occasional chemical spill. A hangar floor sees aircraft tires inflated far above car tire pressure, jack pads and tow bars that concentrate load on a small footprint, and fluids that attack some coating chemistries within hours. It is also a space where people work on their knees, drag hoses and roll heavy tool carts, so the finish has to be cleanable and safe underfoot.

The work usually also has a schedule constraint. Aircraft have to go somewhere while the floor cures, so hangar projects are usually phased by bay or by section. That makes cure time a specification item, not an afterthought, and it is covered again in the checklist below.

Fluid Exposure: Fuels, Hydraulic Fluid and De-Icing

Hangar floors are exposed to aviation fuels such as Jet-A and Avgas, hydraulic fluids such as Skydrol, engine oils, cleaning solvents and de-icing fluids, and the coating must be chemically resistant to the ones the building actually sees. List the fluids first. The system follows from the list.

Fuels are a common spill. Jet-A is a kerosene-type fuel and Avgas is a gasoline-type fuel, and a drip or a fuel-tank sump drain can leave a puddle that sits for hours. A standard epoxy can soften or stain under prolonged contact, so the question for any bidder is how long the proposed system is rated to be in contact with each fuel before it is cleaned.

Phosphate-ester hydraulic fluids such as Skydrol are a separate case. They are known for being aggressive on many paints and some resin systems, and they tend to spray rather than drip when a line fails. A system that handles fuel well is not automatically rated for Skydrol, so ask for the manufacturer's chemical resistance chart and look for the specific fluid by name, not a general statement about chemicals.

De-icing and anti-icing fluids are glycol-based and show up on floors when aircraft are brought in wet. They are usually less aggressive than fuel or hydraulic fluid, but they are slippery and they leave residue, so they affect cleaning and traction more than coating survival.

The table below shows the common exposure classes and what to ask for. Ratings vary by product and by contact time, so treat it as a framework for questions, not as a rating.

FluidTypical SourceWhat to Ask the Installer
Jet-A, AvgasFuel drips, tank sumps, refuelingRated contact time in hours or days, and cleanup interval
Skydrol and similar phosphate-ester fluidsHydraulic line failures, servicingNamed fluid on the manufacturer's chemical resistance chart
Engine and gear oilsLeaks under parked aircraftStain resistance and cleanability of the topcoat
Glycol de-icing fluidWet aircraft entering the hangarTraction when wet and residue removal routine
Solvents, degreasersParts washing, maintenanceApproved cleaning products that will not soften the coating

When fluid exposure is heavy, the topcoat chemistry matters as much as the base coat. A urethane or polyaspartic topcoat is often specified over epoxy for better resistance and color stability, and our guide to epoxy against polyurethane floors explains where each belongs in a system. For very aggressive chemical and thermal exposure, some owners look at urethane cement, compared in our urethane cement against epoxy post.

Loads: Aircraft Tires, Jacks, Tugs and Tool Carts

A hangar floor has to carry two kinds of load: rolling loads from aircraft tires and tugs, and point loads from jacks, stands and outriggers. The slab carries the structure, but the coating has to resist the pressure at the surface without crushing, tracking or delaminating.

Tire contact pressure is the number to watch. Light general aviation aircraft run modest tire pressures, while business jets and heavier aircraft run much higher, often well above 100 psi. That is a concentrated load on a small contact patch, and it is why film thickness and compressive strength of the system matter more in a hangar than in a typical shop.

Point loads are the second concern. A jack pad or a stand can put several thousand pounds through a few square inches. A coating that has not cured fully, or that is too soft, can be indented. Plywood or plates under jacks are common practice, but the coating should still be specified to resist the load that sits on it.

Heavy tow tractors and tool carts add shear forces when they turn on the spot. Tight turns can polish or scuff a coating and, on a poorly bonded floor, begin to lift an edge. Good bond to a properly prepared slab does more for load resistance than any single additive.

Because aircraft weights and tire pressures vary widely, do not rely on a general number. Give the bidder the heaviest aircraft that will be parked or serviced, its gear configuration and its tire pressure from the manufacturer's data, and ask them to confirm the system is suitable. For overall system options for heavy-duty floors, see our comparison of industrial concrete floor systems.

Load TypeTypical SourceSpecification Response
Aircraft tire contact pressureLight aircraft to business jets, tens to 100+ psiBuild thickness and compressive strength confirmed against the heaviest aircraft
Jack and stand point loadsMaintenance on jacks and standsFully cured, hard system plus plates or pads under stands
Tug and tractor shearMoving aircraft in and outStrong bond, correct surface profile, durable topcoat
Tool carts and liftsDaily maintenance trafficAbrasion-resistant topcoat, ASTM D4060 data where available

Abrasion resistance is commonly reported with ASTM D4060, the Taber test, where a lower weight loss indicates a harder-wearing surface. Ask for it on the topcoat, with the wheel and load stated, because results are only comparable when the test conditions match. Our epoxy floor thickness guide covers how mils and coats relate to wear.

Slope, Drains and Fire-Code Considerations

Hangar floors are generally sloped toward drains so spilled fuel and wash water leave the work area, and a coating must preserve that slope, seal around the drains and finish cleanly at their edges. A coating that fills a low spot or builds up around a drain can create a place where fluid collects, which is exactly the opposite of the design intent.

NFPA 409, the standard on aircraft hangars, addresses construction, fire protection and floor drainage for certain hangar types and groups. Which requirements apply depends on the size and use of the hangar and on the authority having jurisdiction, so confirm the applicable edition and the local interpretation with the fire marshal or your insurer before design. A coating contractor does not decide the fire-code category, but the coating should not undermine whatever the code requires.

In practice there are four checks. First, confirm the existing slope before coating, because a floor that already ponds water will not be fixed by a thin film. Second, ask how the system terminates at each drain, trench or sump, usually with a clean edge and a flexible joint rather than a feathered coating. Third, avoid flood coats that are poured to level, which can flatten slope. Fourth, have the contractor mark and photograph drain and sump details so they can be maintained later.

If an existing floor ponds or has trenches that need rework, that is a slab and drainage job first, and the coating comes after. Coating over a drainage problem hides it for a few months and then fails at the same low spot.

Joints, Cracks and Slab Condition

A coating is only as sound as the slab under it, so joints, cracks, moisture and surface profile must be dealt with before any resin goes down. In a hangar these defects are common, because large slabs move with temperature and heavy loads, and old fuel contamination can sit in the concrete.

Control and expansion joints move, and a rigid coating over a moving joint will crack along it. The usual approach is to treat saw-cut control joints with a semi-rigid filler once the slab has finished shrinking, and to leave true expansion and isolation joints open with a flexible, fuel-resistant sealant that is rated for the fluids in the building. Do not let a bidder simply coat over a working joint.

Cracks should be routed and filled, with larger cracks and spalls repaired using a rigid repair material before coating. Our guide to epoxy over cracked or stained concrete explains what repair a floor needs and which defects ask for more than a coating.

Surface profile matters because the resin has to mechanically bond to the slab. The International Concrete Repair Institute defines concrete surface profile, CSP, on a scale from 1 to 9. Thin films usually call for a lower profile and heavier systems for a deeper one, and the correct CSP for a given product is on its data sheet. Diamond grinding or shot blasting, plus vacuum collection, is the normal route.

Moisture and contamination are the two hidden problems. Slab moisture can push a coating off the floor from below, and jet fuel that soaked into old concrete can interfere with bond. Moisture tests such as ASTM F1869 (calcium chloride) and F2170 (in-situ relative humidity) are standard, and the allowable level is set by the coating manufacturer. Our guide to concrete slab moisture testing before epoxy covers methods and fixes. For old fuel contamination, ask how the contractor will test for and treat it, which may include grinding off the affected layer.

Light Reflectance, Slip Resistance and Static Control

Three secondary requirements are easy to overlook: how much light the floor returns, how it behaves when wet, and whether it needs to control static. Each one is a specification item with its own trade-offs.

Light reflectance is why many hangar owners choose a light gray or off-white floor. A lighter, glossy surface bounces overhead light back up into the space and into the underside of the aircraft, which helps inspections and general work lighting. The trade-off is that a glossy floor shows scuffs, tire marks and fluid, and it is more slippery when wet. A satin finish is a common compromise.

Slip resistance deserves the same care. Hangar floors get wet with wash water, de-icing fluid and condensation, and fluids make smooth coatings slick. A fine broadcast aggregate or a textured topcoat adds grip, at the cost of a slightly harder floor to clean. The commonly cited wet benchmark is a DCOF of 0.42 under ANSI A326.3, which comes from tile industry practice and is a reference point, not a legal requirement for coatings. Ask for tested values on the exact texture proposed. Our guide to anti-slip epoxy floor options explains the aggregates and how traction is measured.

Static control is not required everywhere. It matters where avionics are serviced, or where fueling or flammable vapors are present, and some owners specify a static-dissipative topcoat in those zones. Where static control is specified, ANSI/ESD S20.20 is a reference for electrostatic discharge control programs. Ask your insurer, fuel supplier or maintenance team what applies, and keep the resistance range and test method in the written specification. The detail on conductive and dissipative ranges is in our ESD flooring standards guide, so it is not repeated here.

A Hangar Floor Coating Specification Checklist

A hangar floor specification should list the fluids, loads, slab condition, slope and drains, joints, finish, cure schedule and documentation, in that order, so every bidder prices the same job. Use the table below as a starting point and adjust it to your hangar.

ItemWhat to Write DownWhy It Matters
FluidsJet-A, Avgas, Skydrol, oils, glycol, solvents, contact timeSelects topcoat chemistry and rating
LoadsHeaviest aircraft, gear layout, tire pressure, jack loadsSets build thickness and system type
System and thicknessBase coat, build, topcoat, total milsAllows like-for-like bids
Surface profileCSP range from the product data sheetBond to the slab
Moisture and contaminationASTM F1869 or F2170 results, fuel contamination planPrevents blistering and bond loss
Slope and drainsExisting slope, drain terminations, NFPA 409 categoryKeeps fluid moving to the drains
Joints and cracksTreatment of control, expansion and crack repairPrevents reflective cracking
FinishColor, gloss level, light reflectance, DCOF targetVisibility and safety
Static controlWhere required, resistance range and test methodDocumented compliance
Cure and phasingFoot traffic, tire traffic and full chemical cure times, bay sequenceReturn to service without damage
DocumentationData sheets, test results, warranty termsRecords for insurers and lessors

Two items deserve a closer look. Cure time is the first. Many coatings are walkable within a day but need several days before wheel traffic and longer before full chemical resistance, so a hangar that has to park aircraft back in quickly should ask for fast-cure topcoats and a written return-to-service schedule. Documentation is the second. Lessors and insurers may ask for data sheets and test results, and having them in a single binder at handover saves effort later.

If you are planning a hangar floor and want a written scope you can compare, tell us the aircraft, the fluids and the schedule limits, and we will walk the floor with you. The same questions apply whether the project is a small T-hangar or a multi-bay facility.

Frequently Asked Questions

What do hangar floor coatings need to resist?
Hangar floors see fuels, hydraulic fluids such as Skydrol, oils, de-icing fluids, aircraft tire loads and point loads from jacks and stands. A system must be chemically resistant, impact tolerant, and easy to clean while holding color and gloss.
Is epoxy good for aircraft hangar floors?
Properly specified epoxy systems are widely used in hangars, often with a chemical-resistant topcoat for fluid exposure. Heavier aircraft or hydraulic fluid exposure may call for urethane-based or specialty systems, so match the system to the aircraft and activities.
Does a hangar floor need to be anti-static?
Not always. Static control matters where avionics are serviced or fueling or flammable vapors are present, and some owners specify static-dissipative topcoats there. Ask your insurer, fuel supplier or maintenance team what applies to your hangar.
How do you handle slope and drains in a hangar floor?
Hangar floors are generally sloped to drains, and fire codes such as NFPA 409 address drainage in certain hangar types. A coating should maintain slope, seal around drains and terminate cleanly, not create low spots that hold fluid.
How long does a hangar floor installation take?
Time depends on size, slab condition and system. Small T-hangars can finish in a few days, while large hangars are phased so aircraft can move. Fast-cure topcoats help return space to service sooner, and a schedule should include the cure window.

Specify a Hangar Floor Written Scope, Free Site Visit

Tell us the aircraft, the fluids and the schedule. We walk the floor and put the system, cure plan and documents in writing.

Hangar Floor CoatingsFree flooring quote
CallQuote